Automated tire recycling EPT/tyre shredEPTEPT
The initial step in tire recycling procession
Heavy obligation physique
Hooks and cross pulling die produced of forty five# steel, tempered and quenched
Outfitted with defense body avoiding the hazards throughout operating
Two series: Hydraulic one particular and mechanic a single
Straightforward to work and modify spare components (hooks and cross pulling die)
Chopping tires into pieces before shredding
Tiny tire pieces are less difficult to approach in shredder
Knives created of YG-twenty steel, EPT making use of time
1 clamping cylinEPTand 1 slicing cylinder
Geared up with a roller system to process big tires
The high-capability shredEPTwas EPTly deveXiHu (West Lake) Dis.Hu (West Lake) Dis.ed for direct size reduction of tires into cleanly lower tire chips, measurement 50×50 mm. Cutting shafts for the production of larger tire chips are available higher torque at reduced pace lower even the strongest tires into parts.
All building traits are developed for steady operation in orEPTto obtain maximum throughput rates at cheapest costs.
Very exact tolerances in between the chopping knives create cleanly reduce tire chips at minimal power consumption.
The reducing knives manufactured of substantial quality alloy steel can be re-sharpened and reused which will increase the provider daily life and minimizes the operating charges.
The full reducing chamber is lined with challenging use plates.
Big doors enable for simple obtain into the reducing chamber.
The shear amongst the two rollers will make tire chips into powders as properly loosen rubbers, steels and textiles
Roller human body produced of cast steel
Floor of roller manufactured of alloy steel, welded when worn out
One particular flat surface roller and one particular teethed roller, higher throughput of powders
Bottom produced of cast iron
Emergency stop when overload
Length among the two rollers can be modified.
Tough gear EPT
Geared up with screening EPT, magnetic separator and fiber separator, 99% purified rubbers will be acquired.
Finals: eight-30 mesh
Closing Merchandise(five-one hundred twenty mesh tyre powder), As photograph:
The exact same time, Tyre powEPTis widely use in several sector. It can make rubber tile, reclaimed rubber, automobile portion Ect other folks.
2-Reclaimed rubber Making Line From Tyre Powder:
1. Dynamic desulfurization tank (1 sets
Dynamic desulfurization tank
two. Open up miXiHu (West Lake) Dis.ng mill (you need two-3 sets)
1. Diameter of roller: 450mm
two. Working length of roller: 1200mm
three. Velocity of front roller: 24.26m/min
4. Friction ration of two rollers: 1: 1.27
5. Max hole: 15mm
6. Potential: twenty five-50kgs
seven. Wieght: 2000kgs
eight. Motor EPT: 55KW
nine. Dimension: 6150*2280*2000mm
three. Rubber refiner( one sets)
one. Front rolle diameter: 480mm (drum )
2. Rear roller diameter: 612mm (drum)
3. Operating length of roller: 800 mm
4. Front roller linear speed: 22.97m/min
five. Velocity ratio of two rollers(front/rear): 1: 1.eighty two
6. MAX Hole: 15mm
7. Motor EPT: 55KW
8. Dimension: 4700*2100*1480mm
Last EPT(RECLAIMED EPT):
|EPT tire pre-processing , you will get lt 50*50MM rubber crumb|
|one||Solitary hook debeader||LS-1200||one||eleven KW|
|two||EPT tyre cutter||WTC-a hundred and twenty||1||5.five KW|
|three/4||EPT tyre shredder( with EPT tyre conveyor)||ZPS900||one||sixty one.5 KW|
|Rubber powder processing: you will get 3-8 MM rubber powder,at the exact same time, independent the fiber and steel wire|
|five||Tyre crusher||XK560||1||75 KW|
|6||Big conveyor gear||BCL-eight||two||2 KW|
|seven||Little conveyor equipment||BCL-three||one||one.1 KW|
|eight||Massive Magnet separator||BMS22||1||2.2 KW|
|nine||Little Magnet separator||SMS-1||one||1.1 KW|
|ten||Large Shaking display||BSS-8||1||7.5 KW|
|11||Modest Shaking display||SSS-three||one||3 KW|
|twelve||Fiber separator||FS110||one||11 KW|
|thirteen||Wonderful grinder||XMF420||one||32.4 kw|
|14||Circle shaking screen||DIA600||1||2.two kw|