rubber cracker mill for tire recycling EPT
The very first phase in tire recycling procession
Weighty obligation entire body
Hooks and cross pulling die produced of 45# metal, tempered and quenched
Equipped with security frame steering clear of the dangers throughout working
Two collection: Hydraulic 1 and mechanic one
Simple to operate and modify spare components (hooks and cross pulling die)
Cutting tires into parts ahead of shredding
Small tire items are easier to method in shredder
Knives produced of YG-20 metal, EPT making use of time
One particular clamping cylinEPTand a single slicing cylinder
Outfitted with a roller platform to process huge tires
The high-capability shredEPTwas EPTly deveXiHu (West Lake) Dis.Hu (West Lake) Dis.ed for direct dimension reduction of tires into cleanly lower tire chips, size 50×50 mm. Slicing shafts for the creation of greater tire chips are available high torque at minimal speed reduce even the strongest tires into items.
All development traits are developed for constant procedure in orEPTto attain optimum throughput rates at lowest expenses.
Incredibly specific tolerances among the cutting knives produce cleanly cut tire chips at minimal strength usage.
The slicing knives produced of large top quality alloy steel can be re-sharpened and reused which raises the service daily life and minimizes the working fees.
The full slicing chamber is lined with challenging use plates.
Big doorways enable for effortless entry into the slicing chamber.
The shear among the two rollers will make tire chips into powders as properly loosen rubbers, steels and textiles
Roller physique produced of cast metal
Floor of roller manufactured of alloy steel, welded when worn out
A single flat area roller and a single teethed roller, higher throughput of powders
Base produced of solid iron
Crisis quit when overload
Distance amongst the two rollers can be modified.
Difficult equipment EPT
Geared up with screening EPT, magnetic separator and fiber separator, 99% purified rubbers will be got.
Finals: eight-30 mesh
Ultimate Product(5-120 mesh tyre powder), As photograph:
The same time, Tyre powEPTis commonly use in several sector. It can make rubber tile, reclaimed rubber, vehicle portion Ect other folks.
2-Reclaimed rubber Producing Line From Tyre Powder:
one. Dynamic desulfurization tank (one sets
Dynamic desulfurization tank
Product technical specs
2. Open up miXiHu (West Lake) Dis.ng mill (you need to have two-three sets)
1. Diameter of roller: 450mm
two. Operating duration of roller: 1200mm
3. Velocity of entrance roller: 24.26m/min
4. Friction ration of two rollers: 1: 1.27
5. Max hole: 15mm
six. Capacity: twenty five-50kgs
seven. Wieght: 2000kgs
eight. Motor EPT: 55KW
9. Dimension: 6150*2280*2000mm
three. Rubber refiner( 1 sets)
one. Front rolle diameter: 480mm (drum )
two. Rear roller diameter: 612mm (drum)
3. Working duration of roller: 800 mm
four. Front roller linear pace: 22.97m/min
five. Velocity ratio of two rollers(entrance/rear): 1: one.82
six. MAX Hole: 15mm
seven. Motor EPT: 55KW
eight. Dimension: 4700*2100*1480mm
Ultimate EPT(RECLAIMED EPT):
|EPT tire pre-processing , you will get lt fifty*50MM rubber crumb|
|1||Single hook debeader||LS-1200||one||11 KW|
|two||EPT tyre cutter||WTC-one hundred twenty||1||five.5 KW|
|3/four||EPT tyre shredder( with EPT tyre conveyor)||ZPS900||one||61.five KW|
|Rubber powder processing: you will get three-8 MM rubber powder,at the identical time, different the fiber and metal wire|
|five||Tyre crusher||XK560||one||75 KW|
|6||Large conveyor equipment||BCL-eight||2||two KW|
|seven||Little conveyor gear||BCL-three||1||1.1 KW|
|8||Large Magnet separator||BMS22||one||two.two KW|
|9||Small Magnet separator||SMS-1||1||1.one KW|
|ten||Massive Shaking display||BSS-eight||1||7.5 KW|
|11||Tiny Shaking monitor||SSS-three||one||three KW|
|12||Fiber separator||FS110||1||11 KW|
|thirteen||Good grinder||XMF420||1||32.4 kw|
|14||Circle shaking monitor||DIA600||1||2.two kw|